How To Fix Recliner Back That Is Leaning On One Side

Download Article

An uncomfortable recliner chair tin often exist stock-still by making a few adjustments. Changing the force per unit area required to recline the back of the chair can help make your recliner just right for you lot. Adjusting the position of the chair when upright can also assist personalize your chair for the all-time sitting experience.

1
Test your recliner's tension. "Recliner tension" refers to how easily the backrest of the recliner leans backward. Sit down in the recliner and lean dorsum against the backrest. ^[1]
- If information technology'south too difficult to lean dorsum, you'll need to decrease the recliner tension. It can also be a practiced thought to decrease the tension if you have a petite build since reclining the chair will then require less strength.
- If the recliner leans as well far back for comfort, or if it leans back besides easily, you may need to increase the recliner tension. This is usually a proficient thought for heavier individuals, taller individuals, and people needing firmer back support.
2
Tilt the recliner forrad. Make certain the back is in the upright position and the footrest is closed, and carefully tilt the entire recliner forward, to expose the underside of the chair.
- Rest the recliner on the front of the armrests and the acme of its back. Y'all may need both hands to adapt the tension, and the process will be difficult to complete if you attempt to concord the chair the unabridged time.
Advert
3
Look for an aligning machinery. Recliners with adaptable recliner tension should have a pair of pollex wheels or wing nuts below the seat. If no mechanism is present, you may not exist able to adjust the tension.^[two]
- Look for a thumb cycle or wing nut on the right and left of the underside of the chair. Each one should exist positioned at the finish of a bolt, and tension springs should exist connected to the same bolt from the other side.
- The exact placement of the mechanism may vary by manufacturer and model, but in near cases, the mechanism can be establish beneath the seat and toward the back of the recliner. In some instances, the mechanism might exist positioned more toward the bottom center.
four
Rotate the machinery. Turn the thumb wheels or wing nuts clockwise to increase the reclining tension. Turn them counterclockwise to decrease the tension.
- Both wing nuts and thumb wheels should be adjusted in the same way when you're dealing with recliner tension, and then the basic instructions should remain the same.
- Try turning the mechanism with your fingers. If it feels too tight, you lot may need to utilize sturdy pliers instead.
- Work in modest increments. Only plow each bicycle or nut by a quarter turn each time, and echo each adjustment on both sides of the chair to proceed the tension fifty-fifty throughout.
five
Test the adjustment. Return the recliner to its upright position. Sit in the chair and check the recliner tension past extending the leg rest out and leaning back in the chair.
- If the recliner tension feels comfortable enough, you tin can end the process here and relax in your newly adjusted chair.
- If the recliner tension still feels too loose or too stiff, further adjustments will be needed.
vi
Repeat every bit needed. Continue adjusting the recliner's tension as needed by following the same steps. Close the footrest, tilt the chair forrard, and rotate the adjustment mechanism in the proper direction.
- Only adjust the tension by one-quarter turns each time. It might seem tempting to make larger adjustments, but doing so will usually cause you to overcompensate and may accommodate the tension too far in the other management.
- Never loosen or tighten the adjustment machinery all the fashion. Doing and so can cause permanent harm to the tension spring.
- The tension spring should be unable to motility on the bolt after your adjustments. If information technology does move around, it is as well loose, and you should turn the mechanism at least one clockwise one-half-turn.
- Similarly, if the bound becomes completely compressed and besides tight, turn the mechanism at least one counterclockwise half-turn to remedy the problem.

Advertizement

1

Turn your recliner over. With the footrest down and the back in an upright position, gently flip the recliner forwards to reveal the frame underneath the seat of the recliner.
2

Identify the attachment points for the tension springs. Look on either side of the recliner for clips or tabs where springs attach. If the springs are still present, yous just need to locate where they attach to the frame on either end of the spring.
3
Remove the sometime, damaged springs with pliers. Firmly grasp ane end of the spring and disconnect the spring from the frame by pulling and twisting information technology loose with pliers.
- Be conscientious when removing the bound as it will be nether high tension.
- Wear safety goggles to prevent eye damage from potential flight metal.
4
Purchase heavy duty replacement springs. The best springs to utilise in a recliner would be manufacturer replacement parts fabricated for your recliner model.
- Contact a local recliner retailer to inquire if they provide replacement parts.
- Search online for recliner repair or parts dealers.
- If exact matches can't exist establish, ask a retailer which springs would be uniform with your recliner model.
5

Stretch the springs. Place a screwdriver through the loop on each end of the leap. Pull the spring autonomously gently. Slide a nickel in between each coil of the spring to separate the coils. You can also utilise washers in place of nickels.^[3]
vi
Install the springs. Connect i end of the spring to the zipper bespeak of the frame. Using a pair of pliers, pull the spring to attach to the frame at the other cease.
- Be extremely careful when working with springs nether tension. Locking adjustable pliers are proficient to ensure you lot have a solid grip on the spring.
7
Remove the nickels separating the coils. Gently pull the nickels from between each coil with a pair of pliers. In one case the nickels are removed the spring will return to its normal tension.
- Ensure the spring is securely attached at both ends prior to removing the nickels.
viii

Render the recliner to the upright position to test the springs. Flip the recliner dorsum over and sit in it. Lean against the backrest to examination the tension of the springs. There should exist some resistance when y'all lean the backrest dorsum. If the resistance isn't right, you lot may need to try another prepare of springs.

Advertising

one
Sit in the recliner in the upright position. Place your back against the backrest without reclining. Evaluate your recliner'due south pitch for optimum comfort. "Recliner pitch" refers to the height of the chair front when the recliner is in its airtight, up position. You tin can usually adjust the pitch by altering the appropriate bolts at the lesser of the chair.
- If the recliner pitch is too high, your feet won't be able to touch the floor when you lot sit down down. Suit the pitch downward.
- If the recliner pitch is likewise low, your knees will bend upward and above the seat when you're sitting downward, which may pb to discomfort and an unhealthy posture. Consider adjusting the pitch upward.
2
Tilt the recliner forward. With the back in an upright position and the leg remainder closed, lean the entire recliner forward to expose the underside of the chair.
- Allow the recliner to residuum on the elevation of its dorsum and the tips of its armrests when y'all lean it forward. Doing so frees up both hands, making information technology easier to make the necessary adjustments to your chair.
3
Locate the cam bolts. Y'all'll demand to adjust the bolts holding the cam, or full base machinery, deeply in place. These bolts are typically located toward the centre bottom of the chair.^[iv]
- Note that these bolts are non the same as your recliner tension bolts. Your recliner tension bolts feed into the recliner spring, merely the cam bolts are located in the metallic frame of your base mechanism.
- Typically, there should be a total of iv bolts holding the frame in place. Expect for two bolts at the back of the frame (1 on either side of the chair) and two bolts at the front of the frame (one on either side of the chair).
4
Loosen the back bolts. Use an accordingly sized wrench to loosen the cam bolts on either side of the bottom mechanism.
- Make the bolts loose enough for you to jerk the chair around, but exercise not loosen them completely. Practise not remove the bolts or permit them to drop out of the frame.
- Notation that cordless ability ratchets might be easier to utilize than mechanical wrenches for this task. Either option should exist acceptable, though.
5
Remove the front end bolts. Using a wrench or cordless power ratchet, loosen and completely remove the 2 cam bolts at the forepart of the bottom mechanism.
- Unlike the back bolts, the forepart bolts must be completely removed. Keep them nearby and in a rubber place, however, since yous'll be needing them over again soon.
6
Accommodate the frame. Movement the front of the frame up or down to adjust its position. Doing then will also adjust the recliner pitch.
- Slide the frame up and dorsum to bring the front of the chair closer to the basis, to increment its front pitch. Button the frame downward and forward to draw the front of the chair farther away from the footing, thereby increasing its rear pitch.
- Look at the slot at the front of the cam. This expanse is where the front cam bolts fit. For almost recliners, the slot has grooves that allow for 5 different settings, and 2 sets of holes for the bolts to fit through. In total, y'all tin usually alter the pitch to as many as nine dissimilar settings.
- Fifty-fifty small adjustments can brand a large difference in the pitch of the recliner in one case you exam it out, and then it's best to work in small increments.
seven
Return the front end bolts. Once y'all've positioned the cam as desired, insert the front end bolts dorsum into the bottom frame.
- Loosely twist the bolts into the correct holes using your fingers. Check the positioning before y'all proceed. Both bolts should be fitted into the same position on either side of the chair.
- Once the bolts are properly positioned, apply a wrench or power ratchet to tighten them deeply in place.
8
Tighten the dorsum bolts. Using a wrench or cordless ability ratchet, completely tighten the back bolts of the recliner.
- Endeavour to jerk the lesser machinery or frame subsequently tightening all four bolts. It should remain firm and stationary. If not, check and re-tighten the bolts as needed.
ix
Test the pitch. Return the chair to its upright position and sit down down. Your feet should be able to touch on the flooring and your knees should exist bent at an estimate right angle.
- To maintain proper posture, your body should be positioned in right angles at the knees, hips, and elbows. Yous should also have approximately 2 to iii inches (5 to 7.6 cm) of space in between the border of the chair and the back of your calf.
- If the pitch is right, no further adjustments are needed. You tin stop hither and relax in your newly adapted chair.
- If the pitch is nonetheless incorrect, go along adjusting it as needed to ready the problem. Repeat the same sequence of steps to make these additional adjustments.

Add together New Question

Question

Can I bring my legs upwards higher than my heart?

You may have trouble finding a chair that would lift your feet that high, only you could pile cushions or pillows under your feet to raise your legs above your heart.
Question

How do I terminate it from squeaking?

Try some WD-40.
Question

How do I adjust a recliner that is not sitting level from side to side (is slightly tilted)?

Put a sparse piece of wood under some of the legs until it is level. Folded paper works, as well.

Run into more answers

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertizing

Video

Be careful working with springs under tension every bit they may snap and crusade injury.
Cheque with your recliner'southward manufacturer to make sure your model tin be adjusted earlier attempting to alter or remove bolts on the frame.

Cheers for submitting a tip for review!

About This Article

Article Summary 10

To adjust a recliner chair, you can employ the adjustment mechanism to increase or decrease the reclining tension. Get-go, test the reclining tension by leaning back in the chair. If it'southward too easy or hard to lean back, you'll need to conform the tension. To practice this, brand sure the back is upright and the footrest is closed, and tilt the chair frontward onto its armrests. Then, look for an adjustment mechanism, like a thumb wheel or wing nut, on the underside of the chair. Once you've found the machinery, plough it clockwise to increase the reclining tension or counterclockwise to decrease it. When y'all've adjusted the tension, sit down the chair upright and exam it. If the tension'south still likewise strong or weak, repeat the process until yous're happy with information technology. For more tips, including how to replace the tension springs in your recliner chair, read on!

Did this summary help y'all?

Thank you to all authors for creating a page that has been read 336,381 times.